Skip to content
Serving Reseda and nearby cities Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (213) 401-2183

Furnace Repair in Calabasas, CA

Serving Calabasas and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (213) 401-2183

The short answer

Ventora HVAC Repair Service repairs gas furnaces in Calabasas homes, traveling from our base in Reseda about 9 miles away. After a long idle season, most problems trace to a dirty flame sensor, a worn ignitor, or a clogged filter. We explain what failed and your options before any work begins.

In Calabasas, a furnace can sit unused for months. The region's Mediterranean climate brings dry summers and mild winters, so heat is often needed only on cool evenings and during a few colder stretches. That long rest is when small problems build up unnoticed: dust settles on burners, flame sensors pick up a film, and ignitors age. Ventora HVAC Repair Service travels from our shop in Reseda, about 9 miles away, to diagnose and repair gas furnaces in homes throughout the 91302 ZIP code.

Common Furnace Problems in Calabasas Homes

Most calls come in the first time someone switches the thermostat to heat after summer. The system worked last spring, but now it blows cool air, clicks without lighting, or shuts off after a few minutes. Often the fix is a cleaning or a single failed part rather than a major repair.

A brief dusty smell on the first run of the season is normal as settled dust burns off. If the smell lingers, or smells like melting plastic or burning wiring, turn the system off and call for service.

  • Burners light briefly, then shut off, which often points to a dirty flame sensor
  • No ignition at all, from a worn hot surface ignitor or a control board fault
  • Blower runs but the air stays cool, from a gas supply, pressure switch, or ignition problem
  • Short cycling or uneven heat between rooms, from a clogged filter, blocked return, or leaky ducts
  • The furnace trips a safety limit and locks itself out

What Happens During a Furnace Repair Visit

We start by asking what you noticed and when it began. The technician checks the thermostat, filter, and power before opening the furnace, so a simple cause doesn't get missed. Many newer furnaces store fault codes on the control board, which help point to the right component.

From there we test the ignition sequence, inspect the flame sensor and burners, check the inducer motor and pressure switch, confirm the venting is clear, and look over the heat exchanger for cracks or rust. Before any work begins, we explain what failed, what the repair involves, and your options. When the repair is done, we run the furnace through full heating cycles to confirm it lights, holds a flame, and shuts down properly.

Safety Comes First With Gas Heat

A gas furnace that isn't running correctly can create a hazard, so some symptoms shouldn't wait. If you smell gas, leave the house right away and call your gas utility or 911 from outside. If your carbon monoxide alarm sounds, get everyone outside and call emergency services.

Other warning signs include a yellow or flickering burner flame instead of a steady blue one, soot around the furnace, or headaches and nausea that ease when you leave the house. If we find a cracked heat exchanger or a blocked flue, we'll tell you clearly and let you know whether the furnace should stay off until it's fixed.

When Repair Stops Making Sense

Not every furnace is worth fixing. If yours needs repeated repairs, has a failing heat exchanger, or is near the end of its service life, we'll compare repair and replacement side by side so you can decide.

If you're considering a replacement, local rules apply. South Coast AQMD Rule 1111 limits nitrogen oxide emissions from gas furnaces sold and installed in the region, and the district has been amending it toward zero-emission requirements. Because the district sets and revises the compliance dates, check the current rule before planning a new gas furnace.

Some homeowners look at a heat pump instead. Calabasas is outside the City of Los Angeles, and many homes outside the city are served by Southern California Edison rather than LADWP, so the rebates available depend on the utility that serves your address. We confirm the current offer before quoting it. The federal 25C tax credit only covered heat pumps placed in service before December 31, 2025, so it isn't available for new installations.

Keeping Your Furnace Ready Between Uses

Because heat is used only now and then here, a little attention goes a long way. Fall Santa Ana winds can bring hot, dry, dusty spells that clog filters faster than you might expect.

  • Check the filter before the first cold night and replace it if it looks gray or clogged
  • Keep supply and return vents clear of furniture and rugs
  • Move stored items away from a furnace in a garage or closet
  • Run the heat briefly in early fall so problems show up before you need it
  • Test your carbon monoxide alarms on a regular schedule

More services in Calabasas

Related

What to expect

How a visit goes

  1. Find the cause first

    We test the system and track down what is actually wrong before suggesting parts or replacements, so you know what you are paying to fix.

  2. Explain your options

    We tell you what we found, what each option involves, and when a repair is reasonable versus when replacement deserves a closer look. The decision is yours.

  3. Check local rules and rebates

    Furnace rules and utility rebates in the Los Angeles area change and depend on your address. We confirm what currently applies to your home before we bring it up.

FAQ

Common questions

Do you repair furnaces throughout Calabasas?

Yes. We serve homes across the 91302 ZIP code, along with nearby Hidden Hills, Agoura Hills, Simi Valley, Santa Monica, and Beverly Hills.

Why does my furnace blow cold air?

The most common causes are a dirty flame sensor, a worn ignitor, a pressure switch fault, or a gas supply problem. A clogged filter can also cause the furnace to overheat and shut the burners off while the blower keeps running.

Is a burning smell normal when I first turn on the heat?

A dusty smell that fades within a short time is normal after months of sitting idle. A smell that lingers, or one like burning plastic or wiring, means you should turn the system off and have it checked.

Should I repair or replace my furnace?

It depends on the furnace's age, the condition of the heat exchanger, and how often it has needed repairs. We explain both options. If you replace it, check the current South Coast AQMD Rule 1111 requirements first.

Can I get a rebate on a heat pump in Calabasas?

That depends on which utility serves your address. Many homes outside the City of Los Angeles are served by Southern California Edison rather than LADWP, and each utility has its own programs. We confirm the current offer before quoting it.

What should I do if I smell gas near my furnace?

Leave the house right away, avoid using light switches or flames, and call your gas utility or 911 from outside. Once the gas issue is handled, we can repair the furnace.

Tell Us What Your System Is Doing

Whether your AC is blowing warm air, your furnace won't start, or you are thinking about a heat pump, reach out to Ventora HVAC Repair Service. We will diagnose the problem and walk you through your options.

Call (213) 401-2183 Request Service